Safety & Installation Manual

This manual is intended to cover the Safety and Installation of the CM-2/EU or CM-2/UK by a QUALIFIED ELECTRICIAN ONLY. For end user information, please refer to the consumer application that is provided as part of this product offering.

Prior to installing the Sensor, please read this manual carefully. The manual includes important safety information about the device and its installation. Ignoring this important information may cause harm to the installer, other users and damage to the property.

Safety Precaution

Please read and abide by the “Safety Precautions” carefully before installing or using the product.
The notes shown here describe the important information on safety; please follow these instructions at all times.

Description of Symbols

Indicates a potentially dangerous situation which, if not avoided, could result in serious injury or death.

Indicates a potentially dangerous situation which, if not avoided, may result in minor or moderate injury or property damage.

ELECTRIC SHOCK CAN CAUSE INJURY OR DEATH.

THIS DEVICE MUST ONLY BE INSTALLED BY A SUITABLY QUALIFIED ELECTRICIAN

DO NOT ATTEMPT TO RELOCATE OR CHANGE THE LOCATION OF THE DEVICE.

THERE IS A RISK OF ELECTRIC SHOCK AND MALFUNCTION.

Do not attempt to disassemble the device.

There is a danger of electric shock.

Do not install the device and use it in wet areas or places under direct sunlight.

Do not install the device in the bathroom or in humid places.

If you are fitted with an implantable cardiac pacemaker or other medical electrical device such as a defibrillator, please keep a distance of at least 1 metre from this device.

If you are fitted with any other medical device (other than an implantable cardiac pacemaker or other medical electrical device such as a defibrillator), please check with the medical-equipment manufacturer for information on any possible impact on your device by radio waves.

Precautions of Use

THIS DEVICE MUST ONLY BE INSTALLED BY A SUITABLY QUALIFIED ELECTRICIAN.

Only someone who is a qualified electrician is to install this device.
When installing wire connections to this device, please install a dedicated circuit breaker.
Do not push the “Wire removal button” when Sensor is powering on.
When pressing the Reset Button, please use a non-conducting material. Also, do not apply too much force when pressing the Reset Button.
If you notice any abnormality, shut off the circuit using a dedicated shut-off device immediately and stop using the device.
This device cannot be used for electricity billing purposes.
Do not use the device in the vicinity of places such as radio stations, specified low-power radio stations, and amateur radio stations for mobile identification.
Please prepare an appropriate network environment for the de- vice to upload data to the server.
CE and UKCA logo on device label declares the compliance of CE Directives (RED: 2014/53/EU and RoHS: 2011/65/EU) and UKCA regulation the Radio Equipment Regulations 2017. DO NOT remove the device label or modify the device in any way.

Installation Preparation

Sensor - CM-2/EU

CT100 (100A) Large Clamp

CT60 (60A) Small Clamp

CM-2/UK Quantity: -

CM-2/EU Quantity: 2

AWG 14-20 Rated Wiring

Sensor Overview

7: CT Connector

These sockets (CT1, 2, 3, 4) are connecting the CT clamps to CHANNELS 1-4

9: Rating Nameplate

8: Wire Removal Button

Press this button to release the power cables to the device. Please remove the rubber cap to access the button.

4: WIRELESS JOIN Button

Push this button for 5 seconds minimum to connect to a wireless network using WPS.

5:Reset Switch

This button will reset the sensor to its default factory settings.

6: Setting Switch: Pushing this button enables Manual Configuration of the sensor to the Router.

1:NETWORK LED (Blue): The Network LED indicates the communications status. Under normal operation, the Blue LED light is SOLID ON.

2:CT LED (Red): The Red LED will be ON when a CT Clamp is connected incorrectly (opposite orientation). Also, this LED will turn ON during “reverse power” flow (eg. solar-power generation).

3:RADIO LED (Orange)

The Orange LED blinks when the WiFi signal strength is weak.

Installation - Sensor

The wire connection must only be performed by a qualified electrician.

Step 1 - Isolate/Turn off the power

Turn off the main breaker and confirm that there is no power from the grid. If PV is installed, also turn off the PV inverter.

Step 2 - Electrical Connection

Connect a Live wire rated AWG14-20 (not provided) between a branch breaker and the ‘L’ terminal on the sensor.

Connect a Neutral wire rated AWG14-20 (not provided) between the Neutral rail and the ‘N’ terminal on the sensor. Both wires should be stripped between 9-10mm.

Step 3 - Mounting the Sensor

The sensor should be mounted directly to the DIN rail inside the fuse box, or in a suitably rated box next to the fuse box.

Installation - Clamp (s)

Step 1 - Attach CT100 Large Clamp to the Live Feed of the Main Circuit Breaker

Ensure that the clamps arrow is following the flow of electricity into the fuse box (see wiring diagram).

Close the clamp until a click is heard.

This clamp is now secure.

Step 2 – Connect CT100 Large Clamp to the Sensor

Insert the plug end of the CT100 into connection port CT1.

Step 3 – Attach 1x CT60 Small Clamp to Heat Pump Outdoor Unit (if installed)

Insert the plug end of the CT60 into connection port CT2.

For details please check wiring diagram page.

Step 4 – Attach 1x CT60 Small Clamp to PV (if installed)

Insert the plug end of the CT60 into connection port CT3.

For details please check wiring diagram page.

Step 5 – Turn on the power

Turn on the main breaker.

The sensor is now ready to connect to the Wi-Fi network.

If PV is installed, also turn on now.

Network Connection

Ensure that the sensor is within the Wi-Fi range of the router. If required, move the router closer or install a Wi-Fi extender.

Press and hold the WIRELESS JOIN Button of the sensor for longer than 5 seconds.

The NETWORK LED sensor will now flash once every five seconds (wireless connection mode).

Immediately after, press the WPS button on Wi-Fi network router, wait for up to 3 minutes until the NETWORK LED on the sensor is constantly on. The sensor is now connected.

If connection fails, repeat again until the connection is made.

If the sensor fails to connect to the Wi-Fi network router after multiple attempts, or the router does not have a WPS button, then please refer to our trouble shooting section or contact us.

Sensor Registration

Prior to operation, this sensor’s MAC address must be registered in your distributors app. Please refer to here.

Page updated

Report abuse